Brush and Tools

paint the walls in an apartment or room

How to Paint the walls in an apartment or room

High-quality surface staining The process is quite complicated and time-consuming. Therefore, before you start the work, you should familiarize yourself with how to paint the walls in an apartment or room, so that you get a satisfactory result.

Repair activities, regardless of the finishing method, are carried out according to a specific technology, which includes the preliminary preparation of the foundation, the application of the start and finish. Wall painting is no exception.

And the first thing to do is to clean the walls from the old coating. Ideally, the previous finish is removed Concrete. However, in some cases it is very difficult, so the surface is cleaned as much as possible. The main thing is that there are no unstable or sprayed areas.

After all the walls are cleaned, the surface is ground. This will strengthen the foundation, improve its adhesion with finishing materials and in addition it will be dedicated to the surface. If in some areas a fungus or mold was detected, it is necessary to achieve primer with antiseptic properties. Or additionally treat the surface with an antifungal agent

Put training walls under the painting

Depending on the condition of the wall, some specific work will be required to obtain a high-quality paint base. Only on the correctly treated surface can it be applied in such a way that it does not form. It is especially important for glossy paints, with which all the deficiencies in the wall are clearly visible. Therefore, preliminary preparation should be given the closest attention:

First of all, it is necessary to close all cracks and depressions in the wall. As a rule, for this use start plaster, which has good clutch based on a base and is distinguished by low cost. Aligns the surface falls over 2.5 cm. For smaller irregularities, it is better to use putty.

If necessary, it is possible to apply several layers of plaster. It is recommended to comply with one of the rules of professional finishing: Each layer must be dried and projected. After that, wait to dry already primer and only after that apply the next layer. Such an approach will provide a quality and durable base, which will not be painted or stored with wallpaper.

For painting requires thorough alignment of the walls to the ideal smoothness of the surface, so the next step will be the application of the finishing layer with a thickness of no more than 0.5 cm. It is performed using a putty, which has a thin- Staging structure. The composition is distributed on a basis and well aligned.

After complete grazing of the finished layer of putty, the surface is thoroughly sanded on shallow paper to the state of perfect smoothness. The optimal option will be used Friction machinewhich not only speeds up the process, but also improves the quality of work.

Choice of colour, brushes and rollers

However, before staining, it is necessary to determine which dye to use and which tool to apply it. There are several basic formulations that apply to residential staining:

For residence rooms, preferably use Water Level Paints on a latex base. They are considered the most environmentally friendly, virtually no odor and safe for human life and health. For this composition, the optimal choice is a brush made of Artificial fibers or roller brush from the foam rubber.
For rooms with increased moisture content in the air, it is necessary to choose waterproof paints: acrylic and polyvinyl acid. In this case, the special requirements for the brush are not presented, with the exception of the reliability of fixing the hair. The roller can be selected from the same foam or polyester.

If enamels are used for painting, it is best to buy a brush made of Natural material. The roller should also differ resistant to aggressive chemical influences, so choose a tool made of a nylon on a tissue base.
In addition, it is necessary to observe another rule. In the case of self-tarnishing, order the entire volume of paint at once, it will be a guarantee of the lack of “spreading” on the paint of the surfaces. KEL is added to the composition of small portions and carefully stirred. At the same time, remember that the color of the paint in the tank and the resulting shade when applied to the wall has differences, so periodically check the tone.

How to paint the walls?

For each color type there is its own specific application technology, but Head remains common in most of the compositions:

To avoid registering excess paint, the brush is reduced in the container about halfway through. The roller is just received in the bath.
Start painting from the top of a Window Accounts, smoothly moving the main walls of the room. For convenience, divide the wall area Small squareswhich will be gradually sealed. At the same time, each site is processed only after the previous one is completely grazed.

The paint is applied as evenly as possible while maintaining the same layer thickness. To do this, the brush is moved first upwards, then to the left, at the same time trying to distribute the composition over the surface.
The staining should be finished with vertical movements of the brush.
In the case of using a roller with a one-hour paint, the above technology is observed. If the painting is planned in several stages, the starting layers are applied horizontally, and only the last – vertically.
If you need repeated painting, wait until the previous layer dries. At the same time avoid applying a large number of colors, since the composition will begin to flow or flirt then. This is especially true for embossed surfaces. Also, do not use very wet paint.

Read More: Painting colors for Bedroom

Wall design options: film coloring

Often in designer quality Reception Designer reception Use staining walls with strips of different colors. In order for the lines to be smooth and the finish turned out to be of high quality, use the following technology:

Shoot the strip along the relevant lines with such accounting so that later the pencil is under the paint layer.
The edges of the glued Scotch Pass Colorless varnishThis will prevent leakage and paint on the seam.
After the lacquer has dried, the belts can be painted the desired color.

Do not rush to remove the tape ahead of time, wait until the paint is captured. Otherwise, without tilting can not do.

Execution of decorative designs Dubai Sharjah Ajman

In some artistic abilities, you can independently try pattern on the wall. Usually similar works are practiced when you make walls in the kitchen or in the bathroom, but no less interesting, such elements look into residential premises. In these premises, as a rule, paint is used, which is easily applied, easy to care for and distinguished by durability.

There are several techniques for applying an image to the wall surface:

Using a simple pencil when the outlines of the displayed object are transferred to the base. After that, the space inside the perimeter is painted with a brush. Which picture is to illustrate, you can find yourself or get from the Internet.
For more complex drawings, you can use the ordinary projector. The appropriate image is projected on the wall surface and rubbed the pencil, after which the paint is painted.

Follow Brush and Tools Socials

Brush and Tools Facebook

Brush Tools InstagramBrush and Tools Twitter Page

Leave a Comment

Your email address will not be published. Required fields are marked *